Activ-Blue Frameless Flat Roof Skylight

Our bespoke made to order rooflights have been carefully designed to enhance and enlarge specific areas.

Our breakthrough design brightens up areas twice as much as natural light through normal windows amplifying the positive impact on your living environment.

Every flat roof lantern and rooflight we create is proudly manufactured in the UK, using premium locally sourced materials. This guarantees not only structural durability but also an environmentally conscious and aesthetically pleasing product, all while delivering exceptional thermal performance.

• Double or Triple Glazed with 6mm toughened self-cleaning glass
• U Value of only 0.9 W/m
• Contemporary Black Edged Glass
• Warm edge spacer bar filled with Argon gas
• Suitable for flat and pitched roofs
• Compatible with EDPM, GRP, Felt, All Tiles and Corrugated roofs
• We guarantee it will never leak
• All sizes stated on the site is the INTERNAL glass size. There will be a 100mm black border around this specification.

Please click here to see full installation guide online or download PDF here.

Easy-to-install & Hassle Free

All our roof-lights can be easily
installed by roofers and builders – and the below installation guide should
provide everything needed to carry out the installation. 

The roof-lights can be installed on an
insulated upstand coupled with an anodized aluminium angle trim, which your roofer/builder can provide.

All diagrams are used for example
purposes and guidance as all projects vary. They may be based on architecture drawings, so upstand dimensions may vary. Please feel free to contact us should you wish to order a custom designed roof light to suit wider upstands, which
require more than 100mm overhangs.

General Guidelines

Right Glaze roof-lights are one of the
most easiest to install by builders or roofers on the market. Below is a simple
guide, but please feel free to contact us via e-mail or phone should you wish
any further technical support.

How to prepare your roof

The first step in purchasing your
roof-light is to measure the structural opening where the roof-light will be
installed. You should allow for 5mm tolerances all around to allow the bottom pane of the roof light to fit smoothly into the opening.

For example: if your tight opening measurements are 1010mm x 1010mm we would recommend you purchase a roof-light with a bottom pane of 1000mm x 1000mm so it slots in smoothly.

The measurements on our website refer to the STRUCTURAL OPENING. 

For standard units – the top pane
would have a black 100mm overhang all around the top pane. This would then make the overall size of the top pane 1200mm x 1200mm in this example. We can increase the size of the overhang if required, if the up-stand width is wider. This may come at an additional cost.

Preparing Your Roof

Structural glazing silicone is used to
bond the double/triple glazed seal units onto the roof pane to form a roof
light. The roof-light IGU is simply secured onto the timber kerb built by your roofer or builder as part of the roof construction.

The timber upstand should protrude
150mm above the roof. The pitch should be 5 degrees, which would be sufficient enough to allow water to flow down and self-clean.

Installing the roof light

The final step to finish the roof before installing the roof light is to apply your roof covering up to the side of the up-stand to make it weather proof as illustrated below.

The timber up-stand should protrude atleast 150mm above the roof and the pitch should be 5 degrees, sufficient to allow water to flow down. Please note self clean option only works effectively at pitches of 10 degrees or more. Before sealing the product
with the silicone, water can be applied to test the water flow. If pooling
occurs, a higher pitch may be required.

Bottom pane should be supported on 4 sides once set it place, the aluminium angle can be fitted
before the plasterboard and covered with plasterboard or fitted after the
plaster board. Alternatively, a timber batten with aluminium strip on the top
can be fitted to support the roof light.

 Apply adequate compatible low modulus silicone as per silicone suppliers data sheet to the top
of the up-stand firmly placing the roof-light onto the up-stand. Pressure should be applied all round the 100mm overhang to ensure the silicone spreads and seals any gaps and then finish off the silicone all around with silicone tool. Once cured apply structural silicone as per suppliers data sheet to the bottom
aluminium angle trim flat surfaces firmly fitting them in place. Excess
silicone should then be wiped away with a finishing tool. Dowell 791 low
modulus weather proofing silicone and Dowell 895 structural sealant are
compatible with Dowell 3363. Setting blocks can be used to achieve sealant
thickness required.

At this stage the bottom and top panes should be supported. Sealants compatible with the top of the up-stand, aluminium angle trim, glass, setting blocks and Dowell 3363 silicone should be used. Some sealant suppliers may require primer to be applied to the
surface.

Please note all roof lights are made to order and sizes can not be changed once glass is cut or toughened. We recommend the specification, sizes and instructions are reviewed and understood by the installer before proceeding with the order.

Great News! We offer delivery nationwide and offer FREE DELIVERY on all orders within the M25.

DELIVERY COSTS

Once you have added your selected products to your cart, follow through the checkout process and enter in your postcode where the delivery cost will be automatically calculated for you.

We work with trusted delivery partners who ensure that your products reach you safely and intact at a reasonable time scale.

DELIVERY PROCESS

We aim to deliver all orders within 6-8 working days from the day of delivery so you can have them installed as soon as possible.

Once an order is placed you will hear from either ourselves or our trusted delivery partner to inform you when the delivery will be made. This will be agreed with yourselves to ensure there is someone to receive the items. In some instances, tracking codes will be provided so you can follow your order.

We cannot confirm exact delivery times as we deliver nationwide and cannot guarantee when we will arrive at the destination. Unfortunately we cannot take into account traffic times.

Our delivery drivers are alone, and all items are pre-loaded before they depart.
Most products are very heavy, and can range from 15kg to over 200kg. Please ensure there are sufficient helping hands to unload safely.

Right Glaze do not take any responsibility to damaged roof lights during the unloading process as this is the customers responsibility.

In the event a customer does not attend the delivery appointment, we will try to get in touch with all methods before resulting to an alternative and leaving the address.

If there is no other alternative and no contact is made, the product will be returned back to our warehouse. This may result in additional delivery fees if we have to redeliver the items.